DEI 519H (Install Guide) - Remote Start Experts

DEI 519H Three-Channel Receiver Install Guide

What is included

Control module

Two remote transmitters

3-Pin main harness

3-Pin secondary harness

Receiver harness

Power adapter

Venom XHF receiver/antenna

Compatible Transmitters

The receiver is compatible with all of the following DEI transmitters:

Directed Electronics 266 bit transmitters: 470T, 475 Series, 476 Series and 471 Series

Clifford G4 transmitters: 3-button Cello, 4-button OEM, and Radar Master

Avital transmitters: 2-button PIN 820021, 3-button PIN 820031 and 4-button PIN 820041

Product Description

The 519H 3-Channel Receiver uses a computer-based EEPROM Learn Routine to assign individual functions to be controlled by the remote transmitter buttons. The system uses a rolling code, Venom XHF receiver to provide improved range and greater security. The receiver Learn Routine can also be used to program up to twelve of Directed's rolling code transmitters. Additionally, the receiver will store the programmed transmitters in nonvolatile memory, so that if power is lost and then reconnected, the system can recall the transmitter codes from memory. Once initial programming is completed, no additional programming should be required.

Programming the system

Once the unit has been powered up, the system can be programmed using the two program buttons on top of the receiver. If you will only be using the Channel One output, it will not be necessary to program the other outputs.

To Program Channel One

Press and hold Program Button One on the receiver.
The LED will start flashing in groups of one.
While continuing to hold Program Button One, press the transmitter button that you want to control Channel One.
The LED will light steadily when the code has been learned.

To Program Channel Two

Press and hold Program Button Two on the receiver.
The LED will start flashing in groups of two.
While continuing to hold Program Button Two, press the transmitter button that you wish to control Channel Two.
The LED will light steadily when the code has been learned.

To Program Channel Three

Press and hold both program buttons on the receiver simultaneously.
The LED will start flashing in groups of three.
While continuing to hold both program buttons, press the transmitter button(s) that you wish to control Channel Three.
The LED will light steadily when the code has been learned.

Zap Feature

All of the remote transmitters can be deleted from the system's memory by using the Zap feature:

Disconnect power from the unit.
Press and hold Program Buttons One and Two on the receiver simultaneously.
While holding down the program buttons, reconnect power to the unit. Continue to hold down the program buttons until three seconds after power has been reconnected.
The LED will light for one second to indicate that all the remote transmitters have been erased from the system.

Installation

Using the SigH as a Garage Door Interface

The unit should be mounted in a location where a 110 VAC receptacle and the wall mounted garage door switch wires can both be easily accessed.

Using the SigH in a Vehicle Application

Cut the power adapter wire in half, approximately six inches away from the power adapter's transformer.

Using the plug side of the power adapter, insert the plug into the power jack receptacle.

BLACK/WHITE: Fuse this wire using a 10-amp fuse and fuse holder. Connect the wire to the battery positive terminal or the constant 12V supply to the ignition switch.

BLACK: Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather than your own screw. (Screws tend to either strip or loosen with time.) See the following diagram.

BLUE Channel Three negative (-) output: A negative (-) output will be supplied whenever the code controlling Channel Three is received. *

IMPORTANT! The Channel Two and Three Mini-Harness outputs are all 200mA capable and should not be used to drive anything other than a relay or to supply a signal to a module (5517;- 5297;- 5307;- etc.). If the RED wire is used to power anything other than the coil of a relay, the module will be damaged.

NOTE: If the unit is being used as a garage door interface, these outputs can be used in conjunction with a relay to control a second garage door opener. If the unit IS being used in a vehicle, these outputs can trigger a 5517: or any other low current application.

Internal Programming

Operational settings can be changed by cutting jumper wires on the circuit board. To access these jumpers, remove the four screws on the back of the unit and open the module to expose the circuit board. The individual jumper wires are clearly labeled on the circuit board.

Jumper J1
Uncut (default): Pulsed output
Cut: Validity output

In the factory default setting (jumper uncut) the output provided from the on-board relay and the auxiliary outputs will be a pulsed output when the channel is activated remotely. When the jumper is cut, the outputs become validity outputs. A validity output will continue as long as the transmission from the remote transmitter continues.

Jumper J2
This jumper has no function.

Jumper J3
Uncut (default): Code Hopping on
Cut: Code Hopping off

In the factory default setting (jumper uncut), Code Hopping is on. Code Hopping is a feature that uses a mathematical formula called an algorithm to change the code each time the transmitter is used. This technology has been developed to increase the security of the unit. If a transmitter button is pressed while out of range of the receiver, the receiver may fallout of sync with the transmitter. To resynchronize the unit, press the button on the transmitter several times within range of the unit. Cutting this jumper disables the Code Hopping feature.

With Code Hopping off, you may notice a slight increase in range.

* If no code is programmed into the unit, no output will be supplied, Please refer to the "Programming The System" section of this guide for details

Channel One Relav Harness (3 wires. Heavy Gauge)

These wires are connected to the terminals of the on-board Channel One relay. When the control module receives the code programmed into Channel One*, this relay is activated.

YELLOW: Relay common, terminal #30
BROWN: Relay normally open, terminal #87
ORANGE: Relay normally closed. terminal #87A

To interface with a garage door opener, first determine if the garage door openers wall switch connects (normally open switch type), or disconnects the wires (normally closed switch type). Most garage door openers use a normally closed switch. Once the switch type has been determined, interface with the module as shown in the following diagrams

Channel Two and Three Mini-Harness (3-wires, light gauge)

Green Channel Two negative (-) output: The module will output a negative pulse whenever the code controlling Channel Two is received

Red positive (+)12 constant output: This output is used to power the coil (terminal 86) of an relays that are used with the Channel Two or Three outputs.

If no code is programmed into the unit, no output will be supplied, Please refer to the "Programming The System" section of this guide for details.

Normal Operation for the receiver

To manually operate the 5i9H, press and release the appropriate channel button on the receiver for less than one second to activate the desired channel.

IMPORTANT! If a channel button on the receiver is held for more than one second, the 519H will enter the transmitter programming mode.